Advanced cutting tools and complementary CAM toolpaths aim to do for finishing what they have already done for roughing
Within this decade advanced carbide cutting tools used with constant chipload CNC cutting strategies have dramatically increased material removal rates for roughing of mold cores and cavities. Users report roughing cycle-time savings of 25% to 50% or more vs. conventional cutting strategies, while achieving dimensions closer to near net shape after roughing for a more favorable impact on subsequent finishing operations. As impressive as these roughing approaches have been, these strategies are rarely used for finishing cycles, which account for the bulk of the machining time required for most mold cores and cavities. More than anything else, reducing the time it takes to get a core and cavity feature down to the desired surface finish levels will significantly reduce CNC manufacturing costs for molds.
For some time, cutting tool manufacturers and CAM vendors have been working together to dramatically reduce machine cycle times when using solid carbide tools for roughing. Now these partnerships are expanding into finish passes where automated CAM toolpaths are driving innovative cutting tool geometry and vise versa. One such example is the support of the new circle segment cutting tools found in Mastercam’sfinish toolpaths. In many cases, this new tool support can dramatically reduce finish cycle times verses the use of more traditional ball endmills.Where these tools and automated cutting strategies can be applied, cycle time reductions ranging from 50% to better than 80% are being achieved routinely and with superior surface finishes.
Tool Geometry Makes It Possible
Ball endmills have been the go-to cutting tool for surface finishing for decades. They are easy to program and they can have good reach into tight areas of the part. However, for parts that require a great deal of surfacing, ball endmills are part of the problem rather than the solution when targeting better surface quality along with reduction in machine cycle times.
Ball endmills must be used with very small stepovers to reduce the size of cusps in the material. To compensate for this staircase effect and achieve the desired surface finish, a proportionally small stepover or stepdown, e.g. typically 3-5% of the tool’s diameter) must be used. This improves the surface finish, but it reduces the amount of surface area engaged by the tool. Thus, the tool must take many passes to achieve the desired finish. The massive number of passes required to finish a part with a ball endmill accounts for why so much time is invested in finishing vs. roughing of cores and cavities.
Circle segment cutting tools are designed to allow a small diameter tool to have a large effective cutting radius— many times greater than that allowed by the ball endmill. This design reduces the number of finish passes and the depth of the cusps in the material for a substantially better surface finish while achieving shorter cycle times.
The larger cutting radii of these tools (up to 187 times the cutting tools actual diameter) allow extended engagement of the tools with the material and reduce the number of stepdowns required to finish the part. For example, if it takes 30 passes for a ball endmill to finish a set of surfaces, it may take the circle segment tool six passes to do the same work and do it better. In this example, the 80% reduction in the number of passes would translate into a comparable reduction in cycle time for that surface.
Software Makes It Work
Over the past two years four different circle segment tool shapes have come to market:
Barrel-Shape
Oval Form
Taper Form
Lens Shape
Each of these shapes is effective for machining specific types of surface geometries. These surfaces can be straight or have minor undulations and draft angles up to 7°. The tools may be used with3-axis CNC machines, but great care must be taken in defining tool planes to assure accurate finishing results and to ensure the tool is contacting the part in a proper manner. Far better machine cycles are obtained with multi-axis equipment, particularly machines capable of continuous 5-axis machining. When utilizing a machine capable of 3+2 indexing, the ability to apply circle segment tooling vastly improves. Moving to a machine capable of continuous 5-axis machining and the applications for applying this technology broadens even further. Fast, responsive controllers with advanced features like high-speed look-ahead are also advantageous. Then there is the CAM software.
To take advantage of these tools the programmer/machinist must generate sophisticated programsthat continuously present the tool at a precise angle that is dependent on the slope of surface to be finished and the shape of the tool at any given point in the program. The massive amount of code required to create this type of toolpath makes it impractical, if not impossible, to write these programs manually.
To refine this advanced finishing strategy, the circle segment tools and CAM software need to work in sync to coordinate tool definitions and toolpath behaviors, particularly in the 3 + 2 and simultaneous 5-axis machining modes. Better tool library support for these tools was introduced in Mastercam 2017 and the libraries themselves are also compatible with version X9. Circle segment tools can be used within both 3- and 5- axis finishing toolpaths that the users are already familiar with.
The programmer needs only to load the tool definition into the software from downloadable libraries. Then the machining operation applies the appropriate tool compensation for ultra-high efficiency finishing. Proficient multi-axis programmers can also fine-tune parameters to make a good finishing toolpath even more efficient for specific surface requirements.
Manufacturing Laboratory Evaluations
During the evaluation process, toolpaths for high-efficiency finishing were tested extensively in the Mastercam Manufacturing Lab. Testing involved cutting an otherworldly, ten-surface demo part designed to provide at least two realistic applications for comparing the performance of each of the four circle segment tool shapes with that of a ball endmill. (See figure 1).
It took the ball endmill 100 minutes and 34 seconds to machine all the surfaces in succession. Circle segment tools accomplished the same work in 30 minutes and 34 seconds. This represents an aggregate cycle time reduction of 70%. In all instances, surface finish was demonstrably better.
Assessing the Opportunity
What does all this mean to the individual moldmaker? First, it is certainly not time to throw away your ball endmills. There are many surfacing applications where they are still necessary. On the other hand, for some parts and features dramatic finishing cycle reductions achieved with circle segment tools may be able to subtract numerous hours of CNC machining time from the types of cores and cavities you currently machine. Better finishes also lower costs by reducing manual polishing requirements.
The evaluation of this new finishing strategy is easier if you already have multi-axis equipment and the CAM software. It is a simple matter to select circle segment tools and insert them into a program you have already run and adjust stepover/stepdown to achieve a cusp height similar to the one produced by the old ball toolpath. (Minimal changes will also be required to obtain proper tool plane and tool axis control). Then simulate the program with feeds and speeds identical to the ones used previously for the ball endmill. This simple test of time comparisons is likely to be a real eye opener for many mold makers.
Circle segment tools and associated toolpaths constitute an emerging technology with so much potential for reducing manufacturing costs and lead times that mold makers cannot afford to overlook them.
This graphic depicts the ball end milll vs. circle segment cusp height.
Picture: Mastercam
This steering wheel mold and its manufacturer are benefiting from new circle segment tools and sophisticated dynamic finishing CAM toolpaths.
Picture: CNC Software/Mastercam
Circle segment tools and associated toolpaths constitute an emerging technology with much potential for reducing manufacturing costs and lead times for mold makers.
Picture: Emuge Corp
During the evaluation process, toolpaths for high-efficiency finishing were tested extensively in the Mastercam Manufacturing Lab. Testing involved cutting an otherworldly, ten-surface demo part designed to provide at least two realistic applications for comparing the performance of each of the four circle segment tool shapes with that of a ball endmill.
Picture: Mastercam
This Article was written By
Jesse Trinque
CNC Software, Inc.
Tolland, CT
Published in Dynamic Manufacturing India Sep – Oct 2017 issue